Easy Tips To Install Garage Door Hardware

Let’s call it what it is garage doors can be boring. Instead of looking at garage doors as a large dull slab made of aluminum, wood, or fiberglass, think of that it’s a canvas that is begging to be touched by an artist. This guide on how to set up the garage door’s hardware virtually every homeowner or DIYer equipped with the basic tools and free time can become an artist.

The garage door hardware about enhancing the look of your entrance without having to spend in a large amount of dollars. Although they may appear to be basic hardware for garage doors, they are actually quite useful ornaments but there are a few situations where installing this type of hardware can make a huge change.

For example, houses in various developments tend to appear very similar. Moreover, some homeowners might think it is time to break out of the mold. In such cases, well-lit garage doors are the ideal location to display a little of individuality and style by using easy, stylish upgrades like handles and hinges.

Furthermore adding decorative garage door hardware can be a fantastic idea prior to listing the house for sale. A nice appearance is attractive and giving that bare and dull slab to conceal the garage’s contents an overhaul could help make the house sell quicker and at a price that is closer to what the seller is asking.

If you have the garage door that is well-maintained but appear boring the addition of decorative hardware could make all the difference. A handle, some fake hinges, and locks can appear more polished.

Safety Factors

The majority of the time making garage doors is secure. There’s usually no threatening chemicalsand because the modern equipment for garage doors is mainly used for display purposes The components are lightweight and simple to use. But, it’s important to put on the right safety equipment.

If you use a drill with smaller bits it is possible that the bit will snap when it’s under pressure. If it happens, fractured bit’s path can be a bit hazy So DIYers should put on safety spectacles to prevent the risk of sustaining eye injuries. Also, gloves are an excellent idea as they can prevent damage from flying bits and the scrapes and blisters which are commonplace when working on DIY projects.


  • Tape measures
  • The Level (bubble or laser)
  • Pencil
  • Drill
  • Drill bits
  • Screwdriver


  • Decorative garage door hardware (hinges, handles etc.)


1. Map the Hinge Locations and the Map

Begin this project by deciding on the hinges’ places. For most four-panel garage doors, hinge straps work best when there is one placed between the first and second panels and one in between the fifth and fourth panels on either side. Be sure to avoid installing hinges in areas where they could overlap the gap between the two panels.

Make a poke through the screw hole of the bracket, leaving an indentation upon the door. Unhook the hinge, put the bubble level over the mark, then draw a line that is level across the door. Set up the laser level so that it is positioned at the point. Place the hinge on the mark and mark the screw holes.

Repeat this process at every hinge location.

2. The Screw Holes are to be drilled.

With the marks created in step one, you can drill small holes into the shell on the outside for the doors. Follow the instructions of the manufacturer to determine the proper size of the drill. For aluminum or fiberglass doors ensure that you slow down and stop when the bit is able to penetrate the surface in order to avoid the damage of drilling an area that is larger than the one required. For doors made of wood, make sure to drill a hole that is deep enough to accommodate the screws included in the kit.

3. Install the Hinges

Once all the holes are that have been made, put the hinges in place with the hardware included within the kits. Make sure you tighten the screws using an screwdriver to avoid stripping either the hinge’s door, or even the screw’s head. Do not overtighten.

4. Take a measurement and mark the center of the Door

Choose the height you want for the handle. For handles that are vertical it is usually at between the third or second panel. For handles with horizontal handles typically, it is towards the lower part on the panel that is second in.

Utilize your tape measurement to determine the precise centre of the door in any direction from left to right, and draw a tiny pencil line. Utilize the laser level or the bubble level for drawing a plumb vertical line along this line, centered around the desired threshold of the door handle. Set the handle of the door on the marker and then mark screw holes.

5. Drill the holes and install the Handle

Utilizing the same method as previously, make small holes near the marks created at the end of the process Be careful to stop the bit when it is able to penetrate the door. Once the holes have been drilled then, attach the handle with an screwdriver to stop injury from tightening too much.



Leave a Reply